Wol setup

The name might vary between devices. When you find it, change the setting to Enabled. Next, click on the Power Management tab. Make sure you tick the two checkboxes next to Allow this device to wake the computer and Only allow a magic packet to wake the computer.

Sadly, the BIOS menu varies from machine to machine , making it impossible to give precise instructions. Broadly speaking, you'll need to press a particular key while your computer is booting.

Typically, the key is Escape , Delete , or F1. Make sure you turn it on and save your changes. Note: The tab might also be called Power Management , or you might even find the power setting in an Advanced Settings or similar tab.

Magic packets are sent using the OSI-2 layer. In practice, it means anyone on the same network as you could use WoL to boot your computer. Theoretically, WoL only allows computers to be turned on. It won't bypass security checks, password screens, or other forms of security. It also won't allow a computer to be turned off again. However, there have been cases where attackers have used a combination of DHCP and PXE servers to boot a machine with their own boot image.

Doing so gives them access to any unprotected disks on the local network. For such an old technology, Wake-on-LAN retains a surprising number of use cases. If anything, as smart home technology becomes more prevalent, WoL is set to become even more useful for home users.

Best of all, the setup process is surprisingly straightforward. Do you use it? Has this article convinced you to try and set it up? You can leave all your opinions in the comments section below.

Here are the best developer options in Android: disable absolute volume, animation scales, peak refresh rate, and more! Reach out to him for inquires about sponsored content, affiliate agreements, promotions, and any other forms of partnership.

Prior to his writing career, he was a Financial Consultant. Enable Allow this device to wake the computer and Only allow a magic packet to wake the computer.

If these options don't appear or are greyed out, update the network adapter's device drivers. However, it's possible that the network card doesn't support WoL. This is most likely true for wireless network interface cards NICs. Select OK to save the changes and exit that window. You can also close Device Manager. Mac Wake-on-Demand should be enabled by default in version Otherwise, follow these steps:. Go to the Apple menu, then select System Preferences.

Select the Wake for network access check box. Install ethtool with this command:. See if your computer supports Wake-on-LAN:. Look for the Supports Wake on value. If there's a g there, then Wake-on-LAN can be enabled.

If eth0 isn't your default network interface, modify the command to reflect that. The ifconfig -a command lists the available interfaces. Look for the ones with a valid inet addr IP address. If you get a message about the operation not being supported, then you most likely saw a d during the last step, which means you can't enable Wake-on-LAN on Ubuntu.

After the command runs, rerun the one from Step 3 to make sure that the Wake-on value is g instead of d. Now that the computer is set up to use Wake-on-LAN, you need a program that can send the magic packet required to instigate the startup. Since TeamViewer is made specifically for remote access, its WoL function is handy when you need into your computer while away but forgot to turn it on before you left.

One is through the network's public IP address , and the other is through another TeamViewer account on the same network assuming the other computer is on. This lets you wake the computer without configuring router ports since the other local computer that has TeamViewer installed can relay the WoL request internally.

Install it with the following command:. Once installed, enter powerwake followed by the IP address or hostname that should be turned on, like this:. If you followed the steps above, found that your hardware supports Wake-on-LAN without any issues, but it doesn't work when you try to turn on the computer, you might need to enable it through your router.

To do this, log into your router to make some changes. The magic packet that turns on the computer is normally sent as a UDP datagram over port 7 or 9. If this is the case with the program you use to send the packet, and you're trying this from outside the network, open those ports on the router and forward requests to every IP address on the network. Forwarding WoL magic packets to a specific client IP address would be pointless since the powered down computer doesn't have an active IP address.

However, since a specific IP address is necessary when forwarding ports, make sure the ports are forwarded to the broadcast address so that it reaches every client computer. For example, if you determine your router's IP address to be If it's The same is true for other addresses like That way, if the IP address tied to the WoL network changes, the DNS service updates to reflect that change and still lets you wake up the computer.

The DDNS service is only helpful when turning your computer on from outside the network, like from your smartphone when you're not home. This second procedure configures the default client settings for the wake-up proxy settings to apply to all computers in the hierarchy. If you want these settings to apply to only selected computers, create a custom device setting and assign it to a collection that contains the computers that you want to configure for wake-up proxy.

For more information about how to create custom client settings, see How to configure client settings. A computer that receives the wake-up proxy client settings will likely pause its network connection for seconds. This pause occurs because the client must reset the network interface card to enable the wake-up proxy driver on it. To avoid unexpected disruption to your network services, first evaluate wake-up proxy on an isolated and representative network infrastructure.

Then use custom client settings to expand your test to a selected group of computers on several subnets. For more information about how wake-up proxy works, see Plan how to wake up clients.

You can use the following Wake On LAN reports to monitor the installation and configuration of wake-up proxy:. To test whether wake-up proxy is working, test a connection to a sleeping computer.

For example, connect to a shared folder on that computer, or try connecting to the computer using Remote Desktop. If you use Direct Access, check that the IPv6 prefixes work by trying the same tests for a sleeping computer that is currently on the Internet.

Skip to main content. This browser is no longer supported. Download Microsoft Edge More info. Contents Exit focus mode. Please rate your experience Yes No. Any additional feedback? Warning To avoid unexpected disruption to your network services, first evaluate wake-up proxy on an isolated and representative network infrastructure.

Tip To test whether wake-up proxy is working, test a connection to a sleeping computer. Submit and view feedback for This product This page.