Local Call rate Page 9: Windscreen Holder Installation To remove the Car mount from the windscreen; Lift the lever away from the windscreen, then gentle pull the tab on the suction cup to release the suction as you pull the mount away from the windscreen. Local Call rate Page Settings About The About page contains information about your operating system software version.
It also allows you to default the unit or to calibrate the screen to your touches. Local Call rate Page Multi-Media 4 Click on folder to open it and then click on a picture to load it into the viewer.
The compass circle shows the satellites that the unit is receiving and the bar chart shows the signal strength for these satellites Binatone Help Line: for UK only. This is quite normal of products of this type. Additional maps and upgrades: Please visit on www.
Local Call rate Page Introduction 10 minutes again to find a strong signal. You will now be shown the Binatone screen, which shows the progress of the loading software on the yellow bar at the bottom.
Page 17 Time bar — Shows the current time and data as automatically set by the received satellite signals. Also allows for access to the Time Zone setting when tapped.
Then tap OK to confirm the selection, if you do not wish to change countries tap Cancel. Navigate this menu as described above. Tap Back and you will be taken back to the Search from screen. Local Call rate Page Favourites As is may obstruct your view of the screen. Once the option has been selected the menu option will change to show the option which is currently not selected. To Exit from the Trace Record screen tap Close. Tap close from the Browse Map Options screen to return back to the map view.
Local Call rate Page Coordinates To enter a decimal point use the. At this point you can press Cancel to stop route calculation and return back to the previous screen. Local Call rate Page Navigation Screen Estimated arrival time — Shows the time for which you should reach your destination. Note: the screen will return to the last point which was shown on the map. Navi Settings Opens the Navigation settings, which allows you to change the way the unit behaves during navigation.
Trace Record Refer to Page 24, for how to use this feature. Main Menu Exits from navigation and takes you back to the main menu.
Tapping Cancel will exit without saving any of the changes you have made. Tapping OK will save any changes and exit back to the Navigate to menu. Local Call rate Page Go Home Location - This cannot be changed, but shows the location of your favourite as a longitude and latitude co-ordinates. Local Call rate Page Settings Tapping Default will reset the brightness back to the default state. Tapping cancel will exit without saving any of the changes you have made. Tapping Done will save any changes and exit.
Local Call rate Page Volume 4 locked satellite signals which will give a 3D fix. This is clearly indicated at the bottom of the screen by either the word Invalid or valid Binatone Help Line: for UK only. Local Call rate Page Time Zone Setting The display will show the speed limit for the camera as well as the distance to the camera. Along with this the unit will emit a beep sound to warn you of the camera. As the list is populated by possible matches, the matches will be white in colour.
Select the correct entry from the list and tap OK to accept the selected item. The screen will return back to the Address search screen and the chosen city will now appear in the City field. Enter the full postcode, note that you are not required to enter a space in the postcode.
Select the correct entry from the list and tap OK, you will be returned to the Address Search screen. The road field will be automatically filled in by the unit. Note : When the unit is searching, the matched Locations or Post Codes will be shown in the results screen in white text. When the search has completed the first search result will be shown with a blue highlighted bar, If you see your location before the search has completed.
You can select the correct location using the stylus make sure it is shown with a blue highlight before pressing the OK button. In this way you do not have to wait for a full search to be carried out.
This is done in exactly the same way as for entering a city. Thirdly you have the option to enter a house number. Tap crossroad, you will be shown a list of all the other roads which either join or cross the selected road. These places can be either close by or at a distant location. The screen will change to the POI category Menu. Otherwise selecting a category will only show you the POI for the chosen category.
When you have found the category you are looking for tap Next, the screen will change to the Nearest POI screen. Navigate this menu as described above. Tap Back and you will be taken back to the Search from screen. Tap cancel to go back to the Nearest POI screen without narrowing down the results. In order to search further you have to enter a name of road to narrow the search down.
Select the category which you would like to search for a POI. The screen will change to the POI Search menu. Tap on the city field to change the city for which to look for POI, enter a new city using the same method as for when searching via an address.
To narrow down the search even further you can enter a name or part of the name in the name field. The list will be re-populated to only show the matching POI. You can also enter a road to search for POI along. The unit will search for the road in the city stated and show POI which can be found on that road. Tap On Map to see the location of the favourite on the map.
Tap cancel to be taken back to the Search For screen. Note: In order to use a location from the favourites list you will have to store the address previously. This can be done via the Edit Favourites menu see page When you select a favourite from the list a blue window will appear below the item, showing further information on the address, tap on the window to remove it from the screen.
All in one quick and easy step. Tap On Map to see the location of the Recent Destination on the map. Note: When you select a recent destination from the list a blue window will appear below the item, showing further information on the address, tap on this blue window to remove it from the screen. As is may obstruct your view of the screen. Browse Map Options Zoom to Address Allows you to enter an address in the same way as for the address search see page Once the address has been entered, tap OK and the map will automatically centre on the address entered.
Once the option has been selected the menu option will change to show the option which is currently not selected. It then uses this information to draw a track of the route on the map. This enables you to review the route information at a later time. If there are no trace records you will have to record a trace first. The button will always show the option which is currently not selected example display shows Record Off, but the actual recording feature is on and visa versa for Record On.
It is recommended that you start recording after your route has been planned or you are in map tracking mode and that you stop recording once you have reached your destination. This will prevent the unit from continually recording while you are not driving, it will also divide each journey into a separate trace record.
Each recording will be logged with the following information. Viewing the Trace Record on the map: Select the Trace record you want to view, the currently selected trace record will be highlighted orange, then select the option Show it. The screen will change to the View Map screen see page 23 and the trace will be shown as an orange line with green arrows. To remove the trace from the map, re-enter the Trace Record feature again, but this time select Hide it. To Exit from the Trace Record screen tap Close.
Tap close from the Browse Map Options screen to return back to the map view. Coordinates This option allows you to enter the longitude and latitude co-ordinates of the location you are looking for. The screen will change to the Coordinates entry screen. You can enter the coordinates in 2 ways, Degree:Minute or as a decimal. The unit automatically defaults to Degree:Minute format. When entering the Latitude again the letters this time N, S are used to indicate the hemisphere.
To delete an incorrect digit use the back arrow found at the bottom right of the keypad. To enter a decimal point use the. You are now ready to navigate to those points or to simulate the route. Tap Go to begin, the screen will change to either the Navigation screen or to the simulation screen and the unit will calculate the route. At this point you can press Cancel to stop route calculation and return back to the previous screen. Name of next road — Shows the name of the road which you will be on after the next turn.
Planned route — Shows the route ahead which has been calculated by the unit. GPS position indicator — Shows the vehicles location as the route is travelled.
Compass — Shows the direction of North. GPS status — Gold means good, grey means poor and that navigation is not possible. Tap to enter the GPS status screen. See page 37 Map scale bar — Indicates the scale for the currently selected zoom level. Distance bar — At m from the next turn the bar will begin to turn from orange to blue, to give you a visual indication of the distance left to travel. Name of current road — Shows the name of the road you are currently on.
Current speed — Shows the current speed of the vehicle. Note: that this is a general indication of your speed, always observe you speedometer when checking the speed of the vehicle. Distance to destination — Shows the remaining distance to the selected destination. Estimated arrival time — Shows the time for which you should reach your destination. Not all the available options will be shown on the one screen tap on either the Left or Right arrows to view the other available options. If no option is chosen within 10 seconds the screen will automatically return to navigation.
View Route This gives a summary of you planned route. The screen shows the starting point for your planned route. The final destination for the planned route. The total length for the route as well as the time it will take to complete the route based on the speed limits of the roads. There is also a full list of all the turns that you will be requested to make in order to reach your destination.
The list shows a turn indicator, he name of the road you will be turning on to and the distance you will travel on that road till the next turn is reached. If you have a GPS lock, then when you begin moving the map will re-centre around you current GPS position and begin following your movements.
If you do not have a GPS lock then you will have to re-select your start position. Tap Close to go back to the navigation screen. Note: the screen will return to the last point which was shown on the map. Navi Settings Opens the Navigation settings, which allows you to change the way the unit behaves during navigation. In driving direction- It means the unit rotates the map during navigation to always face the direction of your travel.
North OrientatedNow the map is fixed to keep facing North, the map scrolls around your current position. Voice Guidance Allows you to switch off the voice guidance if you wish, the green check box means that voice guidance is switched on. With auto zoom activated the unit will automatically zoom the map during navigation according to your speed, the faster you go the more the map will zoom out to give you a better view of the road ahead.
The green check box means that voice guidance is switched on. If switched on check box is green , then when you deviate from your planned route the unit will automatically re-calculate the route to get you back on track. If switched off then the unit will let you get back on route by your own navigation. It is recommended that you always have Re-calculate turned on. Simulation Speed This allows you to set the speed, at which all of your simulations will be driven.
Tapping Default will reset all of the Navi settings back to their default state. Tapping Cancel will exit without saving any of the changes you have made. Tapping Done will save any changes and exit.
Save Map View The unit will save a picture of the map as it appears on the screen. The picture will be saved as a. Brightness Tap to change the brightness of the screen. Tapping Default will reset the brightness back to the default state. Tapping cancel will exit without saving any of the changes you have made. Volume Tap to change the volume of the unit. Tapping Default will reset the volume back to the default state.
Road Block Whenever you encounter a traffic jam or a closed road you can have the program recalculate a route to circumnavigate this situation as quickly as possible.
However, you must specify a minimum distance after which you want to re-join the original route. Choose a distance that is suitable for the present traffic problem. Trace Record Refer to Page 24, for how to use this feature. Main Menu Exits from navigation and takes you back to the main menu. With the simulation halted you are able to scroll around the map to view the route just as if you were viewing the map normally.
View Route Works in the exact same way as for navigation see the Navigation Options see page 28 Simulate Tap to start simulating; you can use this option if you have delayed the start of the simulation or if you do not want to wait for the start time to elapse. The simulation will start and the unit will drive the route at the speed stated in the Navi settings screen.
The screen will appear the same as for Navigation and all the options are the same. Back Tap to go back to the Navigate To menu screen. GO Tap go to abort the simulation and to begin navigating. Driving Method Tap to change the speed and mode of transport you will be using. The options available are; - Car fast - Car slow - Bicycle - Walker.
When selecting your mode of transport the unit will take this into account when calculating the time it will take you to reach your destination. In addition Car fast assumes fast driving on motorways, choosing this option will slightly favour motorways in the route calculation. Car slow assumes slower driving on motorways, choosing this option will reduce the preference for motorways in the route calculation.
Bicycle and Walker options disables the use of Motorways and Toll roads when the calculating your route. Routing Style Tap to change how the route will be calculated to suit your driving needs. The options available are; - Quickest Route - Shortest Route Selecting Quickest Route will calculate a route which will result in the shortest time between you and your destination, note this will not always be the shortest route.
Similarly Shortest route will calculate a route which has the shortest distance between you and your destination, note this will not always be the quickest route.
By Tapping each you can chose whether or not to allow that parameter during your route calculation, choosing not to have Highways will cause the unit to calculate a route which does not utilise motorways. The same is true for using Ferries or Toll roads.
If the icon is shown with a blue tick then it will be used during route calculation, a red cross means it will be avoided. Tapping Default will reset all of the Route Options back to their default state. Tapping OK will save any changes and exit back to the Navigate to menu. This is a very useful button as your home address will be the destination which is navigated to the most.
Note; In order to use this feature you have to enter you home address first, this can be done from the settings menu. Alternatively if you select the feature without setting your home address, the unit will ask you if you wish to set it now.
Edit Favourites Opens the Favourites List, from here you can add, edit, delete and view your favourite locations on the map. You can add a total of favourites to the list. When you first open the Favourites List it will be empty and you must first add an entry.
Add Tap to add a new entry to the favourites list. The only difference is that you will not be able to choose favourites from this list. Select the location of your favourite in exactly the same way as described in the Navigate to section see page After confirming the location the display will change to the Edit Favourites screen.
The address field will show the information you have just selected. Tap Name the screen will change to show a keypad, you can now enter a name for your favourite.
Tap Tel: the screen will change to show a keypad, you can now enter a telephone number for your favourite. Tap Note the screen will change to show a keypad, you can now enter a note for your favourite. It is not a requirement that you enter additional information for the favourite entry, when it is saved the address will be used as the name automatically if it has not been entered. Location - This cannot be changed, but shows the location of your favourite as a longitude and latitude co-ordinates.
Tap Close to exit without saving. Edit Allows you to edit the information for an already stored favourite location, edit the favourite in the same was as for entering a new entry. By selecting the field you want to change and then delete and re-enter the correct information.
On Map Allows you to view the location of the favourite on the map. The map will centre on the favourite, but it is still possible to scroll the map as well as changing the zoom level.
To return back to the Main Menu tap Close. Recent Destinations Opens the Recent Destinations list, which shows all of the locations you have previously navigated to. You can view there locations on the map. The Recent Destinations list holds 50 recent destinations. The list shows the list number for the location, the time and date the location was last used as well as the address information about the location. On Map - Allows you to view the location of the recent destination on the map.
Tap close to exit back to the Main Menu. In this mode you will be able to find POI and select them with the stylus to be shown more information.
Secondly if you have a valid GPS signal then you can use the map in map tracking mode. Map Scrolling If you have a GPS lock when you are scrolling around the map, the map will always open on your current location.
If you do not have a GPS lock then the map will show the location where the map was last set. With A GPS lock when you move the map, you will see appear on the screen at the right hand side. When you tap this icon you will be automatically taken back to your current GPS position.
Map Tracking Mode As you drive the map will move to follow your position just as if you were navigating, the only difference being that you will not have set a destination to navigate to.
Menu This brings up a simplified version of the Navigation options page, as you are not currently navigating not all of the options are required. There are 6 options available which you can set. When a language is selected not only will it affect the text on the screen, but it will also change the voice command language to the chosen language.
The currently selected language choice is indicated with a blue tick. Once the language has been selected tap Done to confirm. Tap default to set the language back to the default setting, you will have to press Done to confirm this setting. Tap Cancel to exit without making any changes. Set Home Address Allows you to set your home address using the same methods as described under the Navigate to section see page Once set allows you to use the option Go Home from the Main Menu.
Units This option allows you to choose if you want the distances shown on the map and in the Voice commands to be in either miles or kilometres. The option which is highlighted white is the option which is currently selected. About Displays information about the software version which you are using. Tap Close to return to the settings menu.
Note: In order for the changes to the settings to be saved, you must exit the navigational software correctly by pressing on the exit icon shown on the main menu screen. See page 16 GPS Status This screen can be brought up from several different points in the software, by either tapping in the main menu or from the map screen. It can also be found as an option in the Navigation Options menu. Your current speed and the direction you are facing. Along with this information you will find information about the satellites you are receiving signals from.
The green bars show signals which are locked, the orange bars show the signals which have been found but are not locked to. Next to these bars you will see a number this number relates to the number of the satellite for which the signal is coming from.
Tap Close to return to the Main Menu. Note; If you only have 3 locked satellite signals then you only have a 2D fix and certain information will not be available. In order to navigate you need at least 4 locked satellite signals which will give a 3D fix. This is clearly indicated at the bottom of the screen by either the word Invalid or valid 37 Binatone Help Line: for UK only. This only needs to be done when located in the UK. To change the time zone setting tap on the time and date in the main menu.
When you have selected the right option for your current location tap Done, the setting will be saved and the unit will return to the Main Menu.
To exit with out saving tap Cancel. Safety Cameras Your unit comes with hundreds of pre-installed safety cameras locations. When approaching a safety camera the unit will warn you of its presence both visually and audibly. The display will show the speed limit for the camera as well as the distance to the camera. Along with this the unit will emit a beep sound to warn you of the camera.
Please make sure you have correctly spelt your entry.
0コメント